Lunar Module Assembly Photos

Lunar Module Assembly Photos
All photos on this page courtesy Northrop-Grumman History Center
Photos scanned and graciously donated
to MLSM by Mr. Paul Fjeld

Reference diagram for LM axis, locations, and dimensions
Higher resolution version is here

Table of contents:
Ascent Stage
RCS Thrusters
Descent Stage

Lunar Module Designations

LM S/N	Apollo Mission	Call Sign
3	Apollo 9	Spider
4	Apollo 10	Snoopy
5	Apollo 11	Eagle
6	Apollo 12	Intrepid
7	Apollo 13	Aquarius
8	Apollo 14	Antares
10	Apollo 15	Falcon
11	Apollo 16	Orion
12	Apollo 17	Challenger

Manned Missions Only Cited Here
Click here for a full listing of manned Apollo mission vehicles and crews

Ascent Stage
Antennae


LM 9 Rendezvous Radar	LM 9 Rendezvous Radar	LM 5 S-Band Steerable Antenna	LM 5 S-Band Steerable Antenna	S-Band Steerable Antenna	VHF Antenna LM 5

LM 12 IMU "Coffin"

Aft Panels


LM 12	LM 5	LM 5	LM 5	LM 5

Other Exterior Panels & Details


LM 5 Forward panel to left of hatch	LM 5 Forward panel to right of hatch Note panel vent	LM 8 Vent Tube (?)	LM 9 Vent Tube (?)


LM 8 +Y view	LM 8 -Y view	Deadface	Drag Strut

More Aft Panels


Compare to this photo	LM 5	Note panel vent

Forward Hatch & Main Console


LM 12 Hatch	LM 8 Hatch photo used to create hatch detail diagram	LM 8 Main Console	Main console Note illuminated dials, and DSKY in center foreground

Ascent Stage Exterior Photos

Reaction Control System (RCS) Thrusters
All photos in this section are of LM 5 "Eagle"
Quad 1

Quad 2

Quad 3

Quad 4

Note velcro tabs used to attach thermal blankets to the metallic
"skin" of the thruster quads. These were covered with nickel foil strips
and held in place with 3 staples each.

Descent Stage
Top

LM 11

Bottom


Quad 1	Quad 2	Quad 3	Quad 4


+Y Axis View	-Y Axis View	+Z Axis View

All photos above are of LM 5 "Eagle" except as noted.
The photos of the bottom of the descent stage show an inner thermal
blanket of aluminized Kapton which was covered with the
heat shield blanketing on the pad. (seen below)

2 Views of the Heatshield
Two photos of LM 12, "Challenger" showing the final form of heat shield,
made of KEL-F coated nickel foil. This was adopted from LM 5 onwards.

Quad Panels

Refer to this diagram for quad panel numbers
Quad 1

LM 7 "Aquarius" from the ill-fated Apollo 13 mission. This Quad was used
on the early lunar missions to house the deployable S-Band antenna.
On the J-Series missions of Apollos 15, 16, & 17, it carried
the Lunar Roving Vehicle (LRV).
Quad 2

This was also called the Scientific Equipment Bay or, "SEQ Bay", and
held the ALSEP arrays that were deployed on the lunar surface. LM 5
Quad 3

LM 8 photo showing the original configuration of Quad 3 as seen
on all LMs up to Apollo 14. For the J-Series missions of Apollos 15, 16, & 17,
this Quad was reconfigured to carry additional equipment, mainly for
the Lunar Roving Vehicle (LRV). Click here for a full web page on this Quad.
Quad 4

Quad 4 was used to house the Modularized Equipment Stowage Assembly, or "MESA".
The MESA contained most of the equipment the crewmen used while on the lunar surface,
as well as consumables such as PLSS batteries, Lithium Hydroxide canisters, etc.
The MESA also housed the lunar surface TV camera, which was mounted so as to show
the crewmen as they descended the LM ladder to the surface. Fist 5 photos are of LM 5.
The right photo shows LM 10 "Falcon" of Apollo 15, a J-Series configuration.

LM Leg Deployment Mechanism

Go back to Sitemap